Smokin Clean - Extra Absorbent Cotton Pipe Cleaners

Step 1: Gather Your Bong Cleaner and Start Prep

First and foremost, you’ll need to make sure you have what you need for a thorough cleaning. We recommend using 91-99% isopropyl alcohol for the best results. You’ll also want to grab a plastic bag, your bong, and a pair of gloves, if you’d like. 

Step 2: Do a Water Rinse

Start out by doing a simple rinse of your bong with some warm water. Add some to the inside of your bong and give it a few gentle shakes to distribute the water around. 

Empty the water out before you move on, then set your bong inside of the plastic bag you grabbed earlier.

Step 3: Add Some Salt and Alcohol

Place your bagged bong in the sink, then pour in your isopropyl alcohol to a point that’s about half of the usual amount of water you’d add in to smoke.

Next, add some coarse salt through the mouthpiece (the part you place your lips on to inhale) and into the bong. 

Step 4: Get Shakin’

Carefully shake the salt and alcohol mixture in your bong to ensure it gets into all the nooks and crannies.

Step 5: Let it Soak

After you’ve done some shaking, allow your bong to sit and soak for around 30 minutes or so.

Step 6: Empty, Rinse, and Repeat

Step 7: Dispose of Your Bong Bag

​

Read full blog here. 

Step 1: Gather Your Bong Cleaner and Start Prep

We recommend using 91-99% isopropyl alcohol for the best results. You’ll also want to grab a plastic bag, your bong, and a pair of gloves, if you’d like. Before you get started, remove your bong’s bowl (the part you put your flower in) and stem (the long piece the bowl is attached to). You can set these aside to make things easier later on. You may want to clean them separately if they look like they could use some TLC. Dump out any old water, too. 

Step 2: Do a Water Rinse

Start out by doing a simple rinse of your bong with some warm water. Add some to the inside of your bong and give it a few gentle shakes to distribute the water around. Empty the water.

Step 3: Add Some Salt and Alcohol

Place your bagged bong in the sink, then pour in your isopropyl alcohol to a point that’s about half of the usual amount of water you’d add in to smoke.

Next, add some coarse salt through the mouthpiece (the part you place your lips on to inhale) and into the bong.

Step 4: Get Shakin’

Carefully shake the salt and alcohol mixture in your bong to ensure it gets into all the nooks and crannies. You can repeat this process a few times if your piece is especially dirty.

Step 5: Let it Soak

This is really where your plastic bag can come in handy. After you’ve done some shaking, allow your bong to sit and soak for around 30 minutes or so.

Step 6: Empty, Rinse, and Repeat

Carefully remove it from the bag and empty the salt-alcohol mixture inside. Rinse the entire piece with warm water until all residue is gone.

Step 7: Dispose of Your Bong Bag

Once your bong has been sufficiently de-slimed, you can toss your plastic bag. Wipe down any surfaces that you’ve cleaned on, and voila – cleaning completed!

​

For a more in-depth answer, please check out our blog here. 

You can use any type of dried flower you want! CBD or THC. 

​

New to smoking? Read our blog: How to Pack and Smoke a Bowl

Also be sure to check out: All About Weed Measurements

Vape cartridges and disposables can sometimes get clogged and appear to be dead/defective. Holding the device in your hand for a minute or so to warm it up and then doing a few short hard puffs can help get it going. You may have to do this a couple of times to be successful.

Check out our blog for more answers here.